1. The tools
a) The blade
It is very important to have a really sharp blade at all times. This is a project where you are going to use a lot of blades – I bought a box.
As you can see, I think that the ideal blade for this is the Swann-Morton No.15 blade. It is small and you can use the tip for narrow cuts and the rounded part for wider grooves.
b) The other important pieces of kit will be the sanding sticks (better get a good stash of those as well).
Mostly you will need flat ended sticks, you can just cut them to square if rounded. Ruler and scriber for retrieving the lines. And a rivet wheel in the right scale to restore the rivets where lost.
2. To Start
a) Take a deep breath!
b) Using the tip of the blade, scrape along the rivet lines in this case I am scraping just below the panel line. The depth to start with should be shallow followed by a sanding (below) to see the effect. Once you have made a decision about the look you want you can scrape several panels at a time.
c) Alternatively use the middle part of the blade for a wider groove. Study your reference to see which is likely to work best.
In both cases it is important to cut smoothly with no judders (hence the need for a very sharp blade) which will make the effect too rutted.
Once you are used to the routine vary the depths of the cut for effect.
Stuart Mackay says
Sir, I admire your dedication with the oil canning which will surely take such an outstanding model to another Level!
I could, quite easily run out of superlatives for the work that you have done so far!
Truly amazing, and I can hardly wait for each installment of this epic build!
Max Williams says
You’ve made a wonderful job of the oil canning effect Julian, it should look most realistic under a coat of paint.
RossPaton Paton says
Amazing. You tempted to put the transparent side on it?
Julian Seddon says
Hi everyone ! Thanks for the comments. When I started this I was only thinking in terms of the of the fuselage and wings. But as I looked at more and more references I realized that the stress to the aircraft included everything !! The engine nacelles, u/carriage doors,bomb doors etc. this has all taken much longer than I had anticipated.
I am only finishing up what can be seen.
In answer to you Ross two reasons for not using that transparent sides
a. I have only finished the cockpit everything else internally is not touched. The a/c I am modelling P – OS has all the side windows (barring the radio ops) painted over
b. The would have negated the work on stressing the airframe !
Julian Seddon says
some how in (b) above I have missed out the “transparent sides would have negated ” sorry !!!
Michael Chilestone says
There’s some amazing work there Julian; you have more patience than I do!
I assume the site header on the home page is this model as well? I was particularly struck by the weathering on the bombs: they really look as if they’ve spent a few weeks sitting outside on the bomb dump.
Chapeau!
Julian Seddon says
Thanks Michael, yes the header is the same model.
I tried to make the aircraft look as though it has been sitting next to the bombs for a similar time !!
JS
Christopher Woolford says
In 1967 or early ’68 a noted historian, Professor Alan J.P. Taylor, told me that historians are not custodians of the truth. He said historians make interpretations of verifiable facts. The truth, he said can only be told by creative artists. To illustrate his point, he told me to read Len Deighton’s ‘Bomber’. I did and I will never forget it. The bomb bay of your model is likewise chillingly memorable. Well done.
Julian Seddon says
Thank you Christopher. I must say that the word “chillingly” hadn’t occurred to me, but now, bearing in mind what it represents, the contents of the bomb bay of a Lancaster was chillingly fearful to those on the receiving end of it.
Your quote was well extracted !!
JS
Bruce Anders says
An absolutely fantastic build of the model Julian. It has been a joy to watch it’s progress. I sold mine upon the news HKM would be releasing a 48 version. Your build almost makes me regret it
Julian Seddon says
Hi Bruce, I wouldn’t regret it too much !! This was a grind in many ways as, at first, I had no real concept of the amount of oil canning I was faced with. Almost every part of the air frame showed signs of wear, right down to the fasteners on the engine covers !
Looking back it was worth it but it took some resolve to continue from time to time !!
I am sure that HKM will release a very good 1/48th scale version although I have not, as yet, heard about it
Thanks for your comment !
JS